UK
Ireland
Scotland
London
Construction News
30/06/2015
Strada Expands Trench Convector Range
Strada Associates Ltd have expanded their extensive trench convector range with the introduction of 22 fan assisted and 26 natural convection trench models.
The fan assisted models use high efficiency Al/Cu heating coils and variable speed 24 volt DC EC motors linked to low noise tangential fans These achieve high outputs and low noise levels from small casings sizes.
The new range includes 6 off micro channel units, two at only 65mm deep and either 250 or 300mm wide, and four at 80 mm deep in widths of 175, 200, 250 or 300mm.
The smallest of these achieve over 1,000 watts per metre using 75 Deg C feed and 65 Deg C return with a 20 Deg C room.
Additionally, there are a further 16 models available in depths of 90, 110, 125 or 140mm deep and in widths of 175, 200, 250, 300 or 425mm.
All models are available in 100mm increments from 700 to 3,000 and then in 200mm increments up to 4,800mm long.
All casing are galvanised steel with black powder coated internal as standard. However, stainless steel is available as an option.
All other models are available with aluminium, stainless steel or solid timber rollup grilles or aluminium linear grilles except for the six micro channel which are supplied with rigid transverse grilles only.
Matching finish casing edge trims are available to complete a square edged installation into solid/ timber finish floors or an overlapped installation into carpeted or vinyl flooring.
The 24 volt DC EC motor linked to Strada's wall mounted programmable controller or the customers BMS allows constantly variable control of both fan speed and water flow rate to ensure optimum and lowest energy cost operation.
To complete the installation, an extensive range of options are available including remote temperature sensors, hand held remote control for the wall mounted controller, as well as all water valves and actuators.
All units will be supplied with full installation instructions, transport packed and with a sheet timber 'dummy grille' to allow trench installation without the grille.
The grille can then safely installed post floor finishing operations.
To complement this new range, 26 matching dimension natural convection trench units have also been introduced plus four off additional units at .300 mm and 425mm wide and a choice of either 165 or 200mm deep.
Grille and edge trim options are as the fan assisted models.
Strada are still able to offer original ranges of both fan assisted and natural convection trench with stainless steel casing and in client specific lengths.
For more information, visit here.
The fan assisted models use high efficiency Al/Cu heating coils and variable speed 24 volt DC EC motors linked to low noise tangential fans These achieve high outputs and low noise levels from small casings sizes.
The new range includes 6 off micro channel units, two at only 65mm deep and either 250 or 300mm wide, and four at 80 mm deep in widths of 175, 200, 250 or 300mm.
The smallest of these achieve over 1,000 watts per metre using 75 Deg C feed and 65 Deg C return with a 20 Deg C room.
Additionally, there are a further 16 models available in depths of 90, 110, 125 or 140mm deep and in widths of 175, 200, 250, 300 or 425mm.
All models are available in 100mm increments from 700 to 3,000 and then in 200mm increments up to 4,800mm long.
-- Advertisement --
All casing are galvanised steel with black powder coated internal as standard. However, stainless steel is available as an option.
All other models are available with aluminium, stainless steel or solid timber rollup grilles or aluminium linear grilles except for the six micro channel which are supplied with rigid transverse grilles only.
Matching finish casing edge trims are available to complete a square edged installation into solid/ timber finish floors or an overlapped installation into carpeted or vinyl flooring.
The 24 volt DC EC motor linked to Strada's wall mounted programmable controller or the customers BMS allows constantly variable control of both fan speed and water flow rate to ensure optimum and lowest energy cost operation.
To complete the installation, an extensive range of options are available including remote temperature sensors, hand held remote control for the wall mounted controller, as well as all water valves and actuators.
All units will be supplied with full installation instructions, transport packed and with a sheet timber 'dummy grille' to allow trench installation without the grille.
The grille can then safely installed post floor finishing operations.
To complement this new range, 26 matching dimension natural convection trench units have also been introduced plus four off additional units at .300 mm and 425mm wide and a choice of either 165 or 200mm deep.
Grille and edge trim options are as the fan assisted models.
Strada are still able to offer original ranges of both fan assisted and natural convection trench with stainless steel casing and in client specific lengths.
For more information, visit here.
Latest Construction News
29/01/2025
Caddick Construction has been awarded a £43 million contract to deliver the first phase of Cole Waterhouse's flagship regeneration scheme in Digbeth, Birmingham.
The project, known as Upper Trinity Street, marks a significant step in the area’s transformation.
Spanning 182,986 square feet, the re
29/01/2025
McLaren Construction has been appointed by O&H Properties to deliver the first phase of a £60 million Foster & Partners-designed development at the corner of New Bond Street and Grafton Street in London’s West End.
The seven-storey, 5,400 square metre prime retail and office scheme will feature ret
29/01/2025
GMI Construction Group has been awarded a contract to develop three high-specification warehouse units totalling over 175,000 square feet at Precedent Drive, Milton Keynes.
The £20 million project, commissioned by DV5 Last Mile Developments (UK) Ltd, a joint venture between Coltham and Delancey Re
29/01/2025
Plans for 106 sustainable new homes in Southville, a neighbourhood in South Bristol, have been approved as the city seeks to increase housing delivery to address growing demand.
Top 10 award-winning housebuilder The Hill Group will create a £60 million development on Raleigh Road, on land that was
29/01/2025
Bouygues UK has reached a major milestone in the fourth phase of the Hallsville Quarter regeneration project in Canning Town, London.
The project, part of the £3.7 billion Canning Town and Custom House Regeneration Programme, recently held a topping out ceremony, marking the completion of the 11-s
29/01/2025
Willmott Dixon Interiors is carrying out a significant upgrade to the roof of the National Maritime Museum in Greenwich, one of London's most iconic cultural landmarks.
As part of the £12 million project, the company is installing over 23,000 square feet of sun-protected glazing above the museum’s
29/01/2025
Equans has been appointed by Babergh and Mid Suffolk District Councils to carry out crucial decarbonisation work across the councils' housing stock, using funding secured through the Social Housing Decarbonisation Fund (SHDF).
The councils used the South East Consortium's Zero Carbon Framework to s
29/01/2025
In the world of construction, the quest for energy efficiency and sustainability is ever-evolving. Among the array of solutions available, EPS (Expanded Polystyrene) insulation stands out as a versatile and effective option for enhancing the thermal performance of buildings, particularly when used f
29/01/2025
BCP Council has completed significant coastal protection works at Hamworthy Park, ensuring its resilience against erosion for the next 20 years.
A 200-metre stretch of sea wall along the eastern promenade has been reinforced using low-carbon concrete, while new steps have been constructed to improv
29/01/2025
Geo-environmental consultancy and remediation contractor, The LK Group, has strengthened its team with a trio of recruits.
The multidisciplinary company's latest raft of hires comprises a new director, associate director and remediation manager.
The geo-environmental specialist, headquartered i
